Product Code Database
A combined cycle power plant is an assembly of that work in tandem from the same source of heat, converting it into mechanical energy. On land, when used to make electricity the most common type is called a combined cycle gas turbine ( CCGT) plant, which is a kind of gas-fired power plant. The same principle is also used for marine propulsion, where it is called a combined gas and steam (COGAS) plant. Combining two or more thermodynamic cycles improves overall efficiency, which reduces fuel costs.
The principle is that after completing its cycle in the first (usually gas turbine) engine, the working fluid (the exhaust) is still hot enough that a second subsequent heat engine can extract energy from the heat in the exhaust. Usually the heat passes through a heat exchanger so that the two engines can use different working fluids.
By generating power from multiple streams of work, the overall efficiency can be increased by 50–60%. That is, from an overall efficiency of say 43% for a simple cycle with the turbine alone running, to as much as 64% net with the full combined cycle running.
Multiple stage turbine or steam cycles can also be used, but CCGT plants have advantages for both electricity generation and marine power. The gas turbine cycle can often start very quickly, which gives immediate power. This avoids the need for separate expensive , or lets a ship maneuver. Over time the secondary steam cycle will warm up, improving fuel efficiency and providing further power.
In November 2013, the Fraunhofer Institute for Solar Energy Systems ISE assessed the levelised cost of energy for newly built power plants in the German electricity sector. They gave costs of between 78 and €100 /MWh for CCGT plants powered by natural gas. In addition the capital costs of combined cycle power is relatively low, at around $1000/kW, making it one of the cheapest types of generation to install.
In stationary and marine power plants, a widely used combined cycle has a large gas turbine (operating by the Brayton cycle). The turbine's hot exhaust powers a steam power plant (operating by the Rankine cycle). This is a combined cycle gas turbine (CCGT) plant. These achieve a best-of-class real (see below) thermal efficiency of around 64% in base-load operation. In contrast, a single cycle steam power plant is limited to efficiencies from 35 to 42%. Many new power plants utilize CCGTs. Stationary CCGTs burn natural gas or synthesis gas from coal. Ships burn fuel oil.
The cycle a-b-c-d-e-f-a which is the Rankine steam cycle takes place at a lower temperature and is known as the bottoming cycle. Transfer of heat energy from high temperature exhaust gas to water and steam takes place in a waste heat recovery boiler in the bottoming cycle. During the constant pressure process 4-1 the exhaust gases from the gas turbine reject heat. The feed water, wet and super heated steam absorb some of this heat in the process a-b, b-c and c-d.
In a thermal power station, water is the working medium. High pressure steam requires strong, bulky components. High temperatures require expensive alloys made from nickel or cobalt, rather than inexpensive steel. These alloys limit practical steam temperatures to 655 °C while the lower temperature of a steam plant is fixed by the temperature of the cooling water. With these limits, a steam plant has a fixed upper efficiency of 35–42%.
An open circuit gas turbine cycle has a Gas compressor, a combustor and a turbine. For gas turbines the amount of metal that must withstand the high temperatures and pressures is small, and lower quantities of expensive materials can be used. In this type of cycle, the input temperature to the turbine (the firing temperature), is relatively high (900 to 1,400 °C). The output temperature of the flue gas is also high (450 to 650 °C). This is therefore high enough to provide heat for a second cycle which uses steam as the working fluid (a Rankine cycle).
In a combined cycle power plant, the heat of the gas turbine's exhaust is used to generate steam by passing it through a heat recovery steam generator (HRSG) with a live steam temperature between 420 and 580 °C. The condenser of the Rankine cycle is usually cooled by water from a lake, river, sea or . This temperature can be as low as 15 °C.
For large-scale power generation, a typical set would be a 270 MW primary gas turbine coupled to a 130 MW secondary steam turbine, giving a total output of 400 MW. A typical power station might consist of between 1 and 6 such sets.
Gas turbines for large-scale power generation are manufactured by at least four separate groups – General Electric, Siemens, Mitsubishi-Hitachi, and Ansaldo Energia. These groups are also developing, testing and/or marketing gas turbine sizes in excess of 300 MW (for 60 Hz applications) and 400 MW (for 50 Hz applications). Combined cycle units are made up of one or more such gas turbines, each with a waste heat steam generator arranged to supply steam to a single or multiple steam turbines, thus forming a combined cycle block or unit. Combined cycle block sizes offered by three major manufacturers (Alstom, General Electric and Siemens) can range anywhere from 50 MW to well over 1300 MW with costs approaching $670/kW.
Some part of the feed water from the low-pressure zone is transferred to the high-pressure economizer by a booster pump. This economizer heats up the water to its saturation temperature. This saturated water goes through the high-temperature zone of the boiler and is supplied to the high-pressure turbine.
Without supplementary firing, the thermal efficiency of a combined cycle power plant is higher. But more flexible plant operations make a marine CCGT safer by permitting a ship to operate with equipment failures. A flexible stationary plant can make more money. Duct burning raises the flue temperature, which increases the quantity or temperature of the steam (e.g. to 84 bar, 525 degree Celsius). This improves the efficiency of the steam cycle. Supplementary firing lets the plant respond to fluctuations of electrical load, because duct burners can have very good efficiency with partial loads. It can enable higher steam production to compensate for the failure of another unit. Also, coal can be burned in the steam generator as an economical supplementary fuel.
Supplementary firing can raise exhaust temperatures from 600 °C (GT exhaust) to 800 or even 1000 °C. Supplemental firing does not raise the efficiency of most combined cycles. For single boilers it can raise the efficiency if fired to 700–750 °C; for multiple boilers however, the flexibility of the plant should be the major attraction.
"Maximum supplementary firing" is the condition when the maximum fuel is fired with the oxygen available in the gas turbine exhaust.
Where the extension of a gas pipeline is impractical or cannot be economically justified, electricity needs in remote areas can be met with small-scale combined cycle plants using renewable fuels. Instead of natural gas, these syngas and burn agricultural and forestry waste, which is often readily available in rural areas.
Sodium and potassium are removed from residual fuel, crude oil, and heavy distillates by a water washing procedure. A simpler and less expensive purification system will do the same job for light crude and light distillates. A magnesium additive system may also be needed to reduce the corrosive effects if vanadium is present. Fuels requiring such treatment must have a separate fuel-treatment plant and a system of accurate fuel monitoring to assure reliable, low-maintenance operation of gas turbines.
The most fuel-efficient power generation cycles use an unfired heat recovery steam generator (HRSG) with modular pre-engineered components. These unfired steam cycles are also the lowest in initial cost, and they are often part of a single shaft system that is installed as a unit.
Supplementary-fired and multishaft combined-cycle systems are usually selected for specific fuels, applications or situations. For example, cogeneration combined-cycle systems sometimes need more heat, or higher temperatures, and electricity is a lower priority. Multishaft systems with supplementary firing can provide a wider range of temperatures or heat to electric power. Systems burning low quality fuels such as brown coal or peat might use relatively expensive closed-cycle helium turbines as the topping cycle to avoid even more expensive fuel processing and gasification that would be needed by a conventional gas turbine.
A typical single-shaft system has one gas turbine, one steam turbine, one generator and one heat recovery steam generator (HRSG). The gas turbine and steam turbine are both coupled in tandem to a single electrical generator on a single shaft. This arrangement is simpler to operate, smaller, with a lower startup cost.
Single-shaft arrangements can have less flexibility and reliability than multi-shaft systems. With some expense, there are ways to add operational flexibility: Most often, the operator desires to operate the gas turbine as a peaking plant. In these plants, the steam turbine's shaft can be disconnected with a synchro-self-shifting (SSS) clutch, for start up or for simple cycle operation of the gas turbine. Another less common set of options enable more heat or standalone operation of the steam turbine to increase reliability: Duct burning, perhaps with a fresh air blower in the duct and a clutch on the gas turbine side of the shaft.
A multi-shaft system usually has only one steam system for up to three gas turbines. Having only one large steam turbine and heat sink has economies of scale and can have lower cost operations and maintenance. A larger steam turbine can also use higher pressures, for a more efficient steam cycle. However, a multi-shaft system is about 5% higher in initial cost.
The overall plant size and the associated number of gas turbines required can also determine which type of plant is more economical. A collection of single shaft combined cycle power plants can be more costly to operate and maintain, because there are more pieces of equipment. However, it can save interest costs by letting a business add plant capacity as it is needed.
Multiple-pressure reheat steam cycles are applied to combined-cycle systems with gas turbines with exhaust gas temperatures near 600 °C. Single- and multiple-pressure non-reheat steam cycles are applied to combined-cycle systems with gas turbines that have exhaust gas temperatures of 540 °C or less. Selection of the steam cycle for a specific application is determined by an economic evaluation that considers a plant's installed cost, fuel cost and quality, duty cycle, and the costs of interest, business risks, and operations and maintenance.
The electric efficiency of a combined cycle power station, if calculated as electric energy produced as a percentage of the lower heating value of the fuel consumed, can be over 60% when operating new, i.e. unaged, and at continuous output which are ideal conditions.
As with single cycle thermal units, combined cycle units may also deliver low temperature heat energy for industrial processes, district heating and other uses. This is called cogeneration and such power plants are often referred to as a combined heat and power (CHP) plant.
In general, combined cycle efficiencies in service are over 50% on a lower heating value and Gross Output basis. Most combined cycle units, especially the larger units, have peak, steady-state efficiencies on the LHV basis of 55 to 59%.
A limitation of combined cycles is that efficiency is reduced when not running at continuous output. During start up, the second cycle can take time to start up. Thus efficiency is initially much lower until the second cycle is running, which can take an hour or more.
The efficiency of CCGT and GT can also be boosted by pre-cooling combustion air. This increases its density, also increasing the expansion ratio of the turbine. This is practised in hot climates and also has the effect of increasing power output. This is achieved by evaporative cooling of water using a moist matrix placed in the turbine's inlet, or by using Ice storage air conditioning. The latter has the advantage of greater improvements due to the lower temperatures available. Furthermore, ice storage can be used as a means of load control or load shifting since ice can be made during periods of low power demand and, potentially in the future the anticipated high availability of other resources such as renewables during certain periods.
Combustion technology is a proprietary but very active area of research, because fuels, gasification and carburation all affect fuel efficiency. A typical focus is to combine aerodynamic and chemical computer simulations to find combustor designs that assure complete fuel burn up, yet minimize both pollution and dilution of the hot exhaust gases. Some combustors inject other materials, such air or steam, to reduce pollution by reducing the formation of nitrates and ozone.
Another active area of research is the steam generator for the Rankine cycle. Typical plants already use a two-stage steam turbine, reheating the steam between the two stages. When the heat-exchangers' thermal conductivity can be improved, efficiency improves. As in nuclear reactors, tubes might be made thinner (e.g. from stronger or more corrosion-resistant steel). Another approach might use silicon carbide sandwiches, which do not corrode.
There is also some development of modified Rankine cycles. Two promising areas are ammonia/water mixtures, and turbines that utilize supercritical carbon dioxide.
Modern CCGT plants also need software that is precisely tuned to every choice of fuel, equipment, temperature, humidity and pressure. When a plant is improved, the software becomes a moving target. CCGT software is also expensive to test, because actual time is limited on the multimillion-dollar prototypes of new CCGT plants. Testing usually simulates unusual fuels and conditions, but validates the simulations with selected data points measured on actual equipment.
Nearly 60% LHV efficiency (54% HHV efficiency) was reached in the Baglan Bay power station, using a GE H-technology gas turbine with a NEM 3 pressure reheat boiler, using steam from the heat recovery steam generator (HRSG) to cool the turbine blades.
In May 2011 Siemens AG announced they had achieved a 60.75% efficiency with a 578 megawatt SGT5-8000H gas turbine at the Irsching Power Station.
The Chubu Electric’s Nishi-ku, Nagoya power plant 405 MW 7HA is expected to have 62% gross combined cycle efficiency.
On April 28, 2016, the plant run by Électricité de France in Bouchain was certified by Guinness World Records as the world's most efficient combined cycle power plant at 62.22%. It uses a General Electric 9HA, that claimed 41.5% simple cycle efficiency and 61.4% in combined cycle mode, with a gas turbine output of 397 MW to 470 MW and a combined output of 592 MW to 701 MW. Its firing temperature is between , its overall pressure ratio is 21.8 to 1.
In December 2016, Mitsubishi claimed a LHV efficiency of greater than 63% for some members of its J Series turbines.
In December 2017, GE claimed 64% in its latest 826 MW HA plant, up from 63.7%. They said this was due to advances in additive manufacturing and combustion. Their press release said that they planned to achieve 65% by the early 2020s.
Thermodynamic benefits are that daily steam turbine startup losses are eliminated.
Major factors limiting the load output of a combined cycle power plant are the allowed pressure and temperature transients of the steam turbine and the heat recovery steam generator waiting times to establish required steam chemistry conditions and warm-up times for the balance of plant and the main piping system. Those limitations also influence the fast start-up capability of the gas turbine by requiring waiting times. And waiting gas turbines consume gas. The solar component, if the plant is started after sunshine, or before, if there is heat storage, allows the preheat of the steam to the required conditions. That is, the plant is started faster and with less consumption of gas before achieving operating conditions. Operational Flexibility Enhancements of Combined Cycle Power Plants p.3 Economic benefits are that the solar components costs are 25% to 75% those of a Solar Energy Generating Systems plant of the same collector surface. Integrated Solar Combined Cycle Systems
The first such system to come online was the Archimede combined cycle power plant, Italy in 2010, followed by Martin Next Generation Solar Energy Center in Florida, and in 2011 by the Kuraymat ISCC Power Plant in Egypt, Yazd power plant in Iran, Hassi R'mel in Algeria, Ain Beni Mathar in Morocco. In Australia CS Energy's Kogan Creek and Macquarie Generation's Liddell Power Station started construction of a solar Fresnel boost section (44 MW and 9 MW), but the projects never became active.
It is already common in cold climates (such as Finland) to drive community heating systems from a steam power plant's condenser heat. Such cogeneration systems can yield theoretical efficiencies above 95%.
Bottoming cycles producing electricity from the steam condenser's heat exhaust are theoretically possible, but conventional turbines are uneconomically large. The small temperature differences between condensing steam and outside air or water require very large movements of mass to drive the turbines.
Although not reduced to practice, a vortex of air can concentrate the mass flows for a bottoming cycle. Theoretical studies of the Vortex engine show that if built at scale it is an economical bottoming cycle for a large steam Rankine cycle power plant.
|
|
